ASLAN FloorProtect Laminate - MP326
Item No.
DAMP326
ASLAN FloorProtect ASLAN MP 326. The laminating film for indoor and outdoor floor graphics with non-slip safety class R9 Self-adhesive laminating film for floor graphics for outdoor and indoor applications. Film has an anti-slip structure and protects floor graphics from mechanical damage. Best used
Description
ASLAN FloorProtect ASLAN MP 326. The laminating film for indoor and outdoor floor graphics with non-slip safety class R9
Self-adhesive laminating film for floor graphics for outdoor and indoor applications.
Film has an anti-slip structure and protects floor graphics from mechanical damage.
Best used in conjunction with the printed films ASLAN DFP 46 and ASLAN DFP 49, it produces a sandwich structure that is fire-rated according to DIN EN-13501-1.
This applies, inter alia, to reception areas, outside steps and guest rooms.
Face film: Plasticized PVC (monomeric softeners)
Thickness: ~ 125 μm
Adhesive: Acrylic pressure sensitive adhesive
Release liner: PE coated silicone cardboard
Application
For the protection of prints the film should be applied dry. The print must be dried-out at least
48 hours before laminating.
The film should be applied with the ASLAN Application Roll or a plastic squeegee without
felt edge.
Cleaning
We recommend to clean the film with a mop. The product is resistant against standard floor
detergents. The use of a scrubber dryer is also possible. For a partial cleaning a wet cloth
can be used.
If applied outdoors it can also be cleaned with a pressure washer. Please note that a
sufficient distance has to be held and that the edges are not put under too strong pressure in
order to avoid that the edges peel off. Rough surfaces are more difficult to clean than smooth
surfaces.
ASLAN recommends the use of a scouring agent to remove rubber abrasions.
Storage
Before application the films can be stored up to 2 years from date of production. The film
must be stored at room temperature (15-25 °C / 59-77 °F) and at a relative air humidity of 50-
60%. To avoid pressure points appearing on the roll surface, we recommend the rolls be
stored either standing vertically or in a purposely designed `hanging racks'
Self-adhesive laminating film for floor graphics for outdoor and indoor applications.
Film has an anti-slip structure and protects floor graphics from mechanical damage.
Best used in conjunction with the printed films ASLAN DFP 46 and ASLAN DFP 49, it produces a sandwich structure that is fire-rated according to DIN EN-13501-1.
This applies, inter alia, to reception areas, outside steps and guest rooms.
Face film: Plasticized PVC (monomeric softeners)
Thickness: ~ 125 μm
Adhesive: Acrylic pressure sensitive adhesive
Release liner: PE coated silicone cardboard
Application
For the protection of prints the film should be applied dry. The print must be dried-out at least
48 hours before laminating.
The film should be applied with the ASLAN Application Roll or a plastic squeegee without
felt edge.
Cleaning
We recommend to clean the film with a mop. The product is resistant against standard floor
detergents. The use of a scrubber dryer is also possible. For a partial cleaning a wet cloth
can be used.
If applied outdoors it can also be cleaned with a pressure washer. Please note that a
sufficient distance has to be held and that the edges are not put under too strong pressure in
order to avoid that the edges peel off. Rough surfaces are more difficult to clean than smooth
surfaces.
ASLAN recommends the use of a scouring agent to remove rubber abrasions.
Storage
Before application the films can be stored up to 2 years from date of production. The film
must be stored at room temperature (15-25 °C / 59-77 °F) and at a relative air humidity of 50-
60%. To avoid pressure points appearing on the roll surface, we recommend the rolls be
stored either standing vertically or in a purposely designed `hanging racks'
Attachments
